分板機通常是指PCB分板機，也就是線路板分板機。分板機被廣泛應用于電子產品制造業。由于傳統的人工折板方式會有很強的應力產生，對產品品質造成嚴重影響，所以人工折板已基本上被機器分板所取代。
The board dividing machine usually refers to the PCB board dividing machine, namely the circuit board dividing machine. The divider is widely used in electronic products manufacturing industry. Due to the strong stress produced by the traditional manual folding method, which has a serious impact on the product quality, the artificial folding plate has been basically replaced by the machine.
使用方法：usage method:
1.開機前確定電源電壓AC220V.
Confirm the power supply voltage AC220 V before starting
2.打開設備電源開關ON的位置.
Turn on the power switch on
3.行程設定共有五個0、100、200、300、400根據要分的板材選擇合適的行程.
There are five stroke settings: 0, 100, 200, 300 and 400, and the appropriate travel is selected according to the plate to be divided
4.根據板材的厚度來調整切刀的上下高度。根據速度選擇鍵：超快速、快速、中速、慢速四種來選擇設備的運行速度.
Adjust the height of the cutter according to the thickness of the plate. According to the speed selection key: super fast, fast, medium speed, slow speed to select the running speed of the equipment
5.調整平臺的高度，確保放置PCBA板時為水平放置.
Adjust the height of the platform to ensure that the PCBA board is placed horizontally
6.分板時PCBA的邊緣凹槽要卡在分板機的下切刀位置，雙手扶穩PCBA，用腳輕踩踏板，直到切刀走到設定的距離自動停止.
The edge groove of PCBA should be stuck in the position of the lower cutter of the dividing machine. Hold the PCBA with both hands and step on the pedal gently with your foot until the cutter reaches the set distance and stops automatically
注意事項：matters needing attention:
1.本設備僅限用于分板使用。操作員應依公司規定佩戴防靜電手套.
This equipment is only used for dividing board. Operators should wear anti-static gloves according to company regulations
2.操作時應注意手飾，頭發，寬松的衣物避免接近上下刀片，以免造成安全上的問題。
Attention should be paid to hand ornaments, hair and loose clothes during operation, so as to avoid safety problems.
3.切板時，一定要選擇二個位置后，才能踩腳踏板開關，不然刀輪會無運轉.
When cutting the board, you must select two positions before stepping on the pedal switch, otherwise the cutter wheel will not run
4.切板時，如有異常時，迅速壓下緊急開關，并放開腳踏板開關，以防止意外發生.
In case of any abnormality, press down the emergency switch and release the pedal switch to prevent accidents
